Follow Us On Follow us on Facebook
Register
Page 3 of 11 FirstFirst 12345 ... LastLast
Results 21 to 30 of 107
  1. #21
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Right
    Re-lined ceramic pads on the clutch, 1mm thicker overall than the previous disc, new training arm bushings for front and back, and a new crankshaft seal that now I think im going to return & upgrade for a high pressure high temperature seal to cope with the increased crank case pressure

    then we filled the grooves in the bushings with mouldable plastic

    skimmed the flywheel to remove contaminants of oil

    and a reinforcing bar with a jacking point on the rear


    lot of work to do for its first big trial


  2. #22
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    so rain today, back at it & Found why the crank shaft seal has been leaking:

    pulled the rocker cover off to find out where the breather was & why the crank pressure was building up causing oil to be forced out the crank shaft seal
    delighted to find the timing chain as tight as fuck, and the cams all perfect no signs of any damage so alls good in that department


    now onto the rocker cover itself where the breather is behind a splash guard, so with the splash guard removed & I discovered the wire mesh that is clogged to shite with oil, which I think Ill be removing altogether since theres baffles aswell, its a bit overkill & causing restrictions.. but I also noticed this plastic tab shoved down in the compartment of the vent itself, restricting flow... no wonder pressure is building, that tab is marked by the Red arrow, and the half mile of a metal gauze filter


    the tab again marked with red, and the yellow arrow showing the vent out into the air intake downpipe towards the turbo

    and the tab will certinally not be going back in



    im contemplating whether to remove the gauze or part of it just to catch oil, but then again the splash guard completely seals 95% of the oil anyways.. or maybe an oil catch can and then straight out to the air.. Il think about it for now


    went removing the front hubs & wishbones to extend both for camber & more lock... more to come tomorrow



  3. #23
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    shortened the eye for the track rod on the hub 10mm, which makes it lock quicker and further, welding rods used were 29.9 rods very dear cunts at 2.30+vat each but a real clean weld, V'd it out & built it up well so tis very strong



    extended the wishbone 30mm for more camber
    modified vs original


    and how we extended them


    re-track the car next & get a photo of how it looks on the car


  4. #24
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    No shortage of lock now



    and a bit of camber


  5. #25
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Attacked the back arches to take 5 series alloys, cut the arch out & stuck on overfenders




    another project shane went working on... S/S tipped Side Exit Exhaust



    and the hassle... Clutch that we got re-lined after our last bout of crank shaft issues, new seal fitted.... and not enough gasket sealer :/
    the new clutch disc is 1mm thicker than the previous

    and the freshly skimmed flywheel, Forgot to mention we had 0.5mm taken off the step.. which gives the effect of an even thicker clutch disc. This brought it up to almost the equivelant of a full thickness clutch disc giving it Waaaaaaay more bite than before

    the performance blue paint on the new pressure plate now that the old one was contaminated with oil

    cleaned the bell housing out


    put the whole lot back together & was grand, everything ready to run, just bolting back up the started a nut fell down behind the flywheel, and gearbox had to come out enough to get the bolt out.. That was grand, until we put in the slave cylinder and the pin went above the fork unknown to us & burst.. putting brake fluid everywhere... gearbox back out yet again


    pulled in another iS and stole the slave cylinder out of it, along with stealing the alloys off it had an awful problem taking off lock studs with no key for them



    we thought that was grand cleaned the brake fluid out of the bellhousing & threw the lot back in yet again.. Started it up, brought it for a hard spin & came back in to find oil pouring out of the gearbox yet again... this was 10pm saturday night, proceeded to take out the gearbox yet again & found that the cunt was leaking out along the edge where the sump meets the block where we didnt put enough sealer... sealed it up & had the lot back in by midnight.. problem was that that gasket sealer takes 24 hours to cure fully, but it was due to do its first round on the track at 9 the following morning...

    spent until 2am sorting out tyres & doing the final preps for the track day
    welded on the remains of one of the wishbones we cut up for a towing eye

    also moved the battery to the centre of the boot just incase we decided to crash the back into something or someone.. very likely with two noob drifters at the wheel

    it also took longer to load the car onto the car transporter without turning on the engine than it did to take out & put back in the gearbox


  6. #26
    di Member
    Status
    Offline
    User ID
    350
    Join Date
    Aug 2009
    Location
    Cill Dara
    Posts
    550

    Default

    Savage custom work going on here, it's the only way with the bmws! Think I saw you in Tynagh at the last driftfest?


  7. #27
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Quote Originally Posted by blusrule View Post
    Savage custom work going on here, it's the only way with the bmws! Think I saw you in Tynagh at the last driftfest?
    Yep ya did.. may aswell continue from the beginning


    Tynagh Superdrift 24/3/13
    Set off at 5am with just little over 2 hours sleep

    as expected the crank seal gasket started throwing out a bit of oil but not much so we kept going... by the end of the day & a gallon of oil later we were still going with 2nd gear, 3rd was slipping the clutch which is contaminated yet again.. The joys


    Anyways I had an absolute ball, everyone was dead on & had fun polluting the place & blackening the track.. Came home as black as a coal miner & fairly delighted with the car.. Pure addictive Bring on the next day

    anyways... Blackened the track





    more pics







    In terms of drivability, never once used the hydraulic handbrake or clutch kicked, just floored it & the massive amouts of torque spun the tyres instantly Engine is veeeeery responsive to the accelerator plenty of power Delighted with the car apart from the seal which I must now sort out.. Theres a lot of body roll, so I think our only choice now is coilovers..


  8. #28
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Shane decided to get a petrol cunt of a thing for the track.. Continuing my ban on sparkplugs, he had to shove it in a shed in his own place


    plan to fit M50 manifold & chip er up


    threw a bit of weld in the diff

    then we made a straight through for it.. sounds mental now



    alternator off to get sorted, few more bits & pieces to do in the front aswell & to get the thermostat out

    drilled 4 holes in the thermostat on eoinK's reccomendation.. will drill more if it continues to heat while drivin the bag out of it on the slab


    clutch is slippin like fuck, so ordering a ceramic disc for it now too, along with 3 sets of coilovers for the tds, this yolk & another e36 this week.. 195 delivered for JOM bluelines is not bad atall


  9. #29
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Right Update time
    Firstly.. Crankshaft seal pouring oil.. did the sump seal & crank seal twice since & both times leaks.. absolute torture! Still leaking all over the clutch so no 3rd yet again on sunday
    sump down & cleaned

    Engine had to be lifted a few inches to take the sump out


    Thanks Mr. Postman.. Coilovers fitted them, and the rear trailing arm bushings the night before... LastMinute much, got sets for shanes petrol yolk aswell as eoink, and a few paddle clutches for shane, eoin & another lad aswell..


    Anyways: DriftFest Tynagh 19/5/13
    First lap out on track and no power pouring smoke & lagging very bad even with the chip off, only boosting 0.4 bar and then kept tripping into limp mode.. but would spool fine until under pressure, decided it was an air restriction so we pulled out the air filter, dropped it on the bonnet & a good cupfull of sand scattered out of it, as well as being choked with oil... straight away the difference was noticable in power..

    Next round out on track was full power through the first bit of the turn, but kicked into limp mode at the end of the turn... opened the bonnet to find exhaust gasses bellowing out from the exhaust manifold where the EGR connects on, just before the turbo.. ofcourse our cold air intake was left at home by accident so only thing for it was take off the bonnet so it wouldnt be sucking in ehxaust gasses.. and straight away LOTS more power, altho she was down to 1.3 bar boost due to the exhaust pressure dropping.. Unfortunately it was lunchtime before we got full power back into the car, but made for a great afternoon blackening the track

    daniel got a few stickers made up




    And most importantly a short one lap onboard video in HD Full Of The Pipe
    BMW 325TDS Diesel Drifting at DriftFest Tynagh 2013 - YouTube


  10. #30
    Senior Member TorqueWorks's Avatar
    Status
    Offline
    User ID
    2748
    Join Date
    May 2011
    Posts
    155

    Default

    Bit of pollution here, this was before we took off the bonnet so it wasnt getting enough air & just bellowing smoke


    Car doesnt have to be in the picture to know where we just were


    and daniel just doing a bit of landscaping, front lip is not a land leveller


    Shes sitting an awful lot more stable with the coilovers


    bonnet off & it was able to get that air it needed so less smoke




 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •