Fully Loaded Hcr32 - rb25

[B&G Extreme Drifting]

savage build lad fareplay,sure your mate is proud,will keep my eye on this anyway

Thanks very much, it's means alot to me, them kinda comments. He would be and he's with me all the way when I'm out in it cause if that was'nt the case I'd be a lost cause behind the wheel
Cheers again!!

[B&G Extreme Drifting]

Update on car, well shes 110% mechanically bang on, wel I dunno if you'd use that term, maybe cowboy would suit better haha but I hav'nt been this happy with that end of things since brought car home from being ran in & mapped end of 2010.

Suspension wise I'm at bout 95%, happy with that also (last piece of the jig-zaw) for the min driftworks poly bushes for hubs where toe arms connect to



having bit of trouble getting them in, so popped them in2 warm water



Then had bit luck, in ya go



Plan to seem weld the car in winter along with upgrading the cage so still in 2 minds bout this expanding foam, sure I might do the subframe anyways, time will tell

The car needs new brake pads so gonna try take out the trolley during the wk
All criticism welcome lads, like ta know where I'm goin wrong, thanks

[B&G Extreme Drifting]

Update time, suspension is now 110% sorted too. Wasnt as lucky as others wen fittin subframe, it was jus slighty hittin the body but nothin the nissan hammer or sledge wouldnt sort think il get new anti-roll bar bushes & for drop links. no point cuttin corners at this stage
As was saying badly need brake pads so

New uprated PBR pads all round (was gonna go EBC redstuff but no matter what pads are there the hydro wont be shy bout lockin the wheels so there 100% !!)



New Brembos discs drilled & grooved all round!


Massive thanks to Steve (SC86) for help on this 1, absolute gentleman to deal with & very helpful!!

no point havin a big fire and nothin to put it out with

[B&G Extreme Drifting]

decided give calipers bit of clean, gave them a blast of break cleaner and wire brush. then 3 coats later of high tempeture paint



fitted brembozzz and PBR's Front





Rear



Happy out, really sets the TE's off!

[B&G Extreme Drifting]

Small update, right not 100% happy with suspension so gonna change drop links front,a-roll bar bushes all round and outter tie rods (poss teins). was tryin get polys for anti roll bar but not havin much luck. any1 can help me out with that??pulled out all old bits,some were in very bad condition!!



decided to clean up the anti-roll bars, 1in primer



should be sorted out in week or so, any ready for set up with Wez

[tomsheen]

just read all this from start to finish man really well done the car and work gone into
it is top notch.. no corners cut, everything done properly so well done again man..

you seem a sound owld fella too infairness so i wish ya good luck with it man
im sure twill end up perfect just the way ya want it

[B&G Extreme Drifting]

Had engine dampner for RB20 but will not fit since 25 has been fitted! So got new RB25 dampner from Japspeed. Was havin wee look there needs wee adjustments but will fit!

[B&G Extreme Drifting]

just read all this from start to finish man really well done the car and work gone into
it is top notch.. no corners cut, everything done properly so well done again man..

you seem a sound owld fella too infairness so i wish ya good luck with it man
im sure twill end up perfect just the way ya want it

Bang on Tom, sound comment means alot,appreciate that big time!!
now the 2nd statement,not so sure bout that, I'm a bit of a wan.er haha cheers man
hopin to get out for test run soon, should be good,
It will be good
Thanks, sound out