project LOTS OF WORK, 4door r32

[s15_spec_r]

there was a few connectors missing out of the fusebox but i assumed they wer from the auto box, and the block connectors didnt seem to clip together properly, and when it wouldnt start i just put it all down to the loom not working properly, only took bout 20mins to take it out anyway, we didnt actually strip the whole loom just the bit that goes under the windscreen and out to the headlights, and we only took that out when it didnt start, was just as handy to take the dash out for when i fitted the clutch pedal i dont think i would have got it in too handy otherwise,


so should have the interior loom back into it 2moro and will run that wire,............. what will i do? just run a wire from the live on the ignition to the live on the starter? and it should be good?

[gem-s13]

there was a few connectors missing out of the fusebox but i assumed they wer from the auto box, and the block connectors didnt seem to clip together properly, and when it wouldnt start i just put it all down to the loom not working properly, only took bout 20mins to take it out anyway, we didnt actually strip the whole loom just the bit that goes under the windscreen and out to the headlights, and we only took that out when it didnt start, was just as handy to take the dash out for when i fitted the clutch pedal i dont think i would have got it in too handy otherwise,


so should have the interior loom back into it 2moro and will run that wire,............. what will i do? just run a wire from the live on the ignition to the live on the starter? and it should be good?

ye lad just one wire should do it from the trigger wire on the ignition or the triggger for the unloader relay

[s15_spec_r]

im guessin its a red wire? im hopeless at wiring so i have to ask

[Newsome]

When the loom is out would you not just rerun the manual loom to save any messing?? And then use the manual clocks aswel.

[s15_spec_r]

i dont hav the manual loom to hand or the clock. I left it al in the donar car when i scrapped it..... Wat a terrible idea that was. I do see your point tho. But i never do things the easy way

[s15_spec_r]

wel i tried running the wire fromt he ignition to the starter and i blew a 75amp fuse ( which was impossible to find a replacement) also fried a few more relays so i had no option but to change the interior loom, fair play to jonny (200sx) he stepped up with everything i needed, so off to tramore with me to pick them up,

so we fitted that and it turned over on the first turn on the key, we bled the rad and took if for its first spin................................ it lasted all of 5 mins until DISASTER STRUCK

the water pump exploded out of the block and put the fan out through the rad,
so we stripped the water pump out of the auto engine and re-fitted that yesterday,
also replaced the rad with a very good nick alluminium one


also took a trip to icetronix to pick up my carbon GTR bonnet, also got a set of pins off lorcan in drift2,
also got around to re-fitted and trimming the front bumper,


so i was bored and couldnt wait until i put my meisters on it



they require 225's fittin to the front and a bit of camber for them to fit snug,

on a good note, the rb25 turbo i fitted made a serious job to it im delighted with it,
just have to bleed the alloy rad and its good to go again (fingers crossed)

at this point i have to say a MASSIVE thanks to waytoofastforu for all his help with the build, id be rightly wanked without em,

really dunno what todo about the wheels yet, i love how low its sitting with the 16's,
and i cant afford to run 18's on the rear for skiddin,
anywho. WHAT YA's THINK??

[GTSr32]

looking good ted can i please have ur meisters

Hope ur happy with the bonnet??? ill have an up date later too

[git]

lookin well ! is your front wheel a bit pushed back ? tink its called castor could be wrong ?

[jdmjimmy]

looks savage..

remove spoiler & mudflaps

gtr front bumper and lip

nice a/m skirts and rear bumper

schweeet!

iv actually got 32 rear spats if there any good t'ya

[s15_spec_r]

@chris. yeh bud im over the moon with the bonnet, its a serious piece of work in fairness, good job i had the bonnet pins, the latch on the bonnet was about 2 inchs further back from my catch,


@git no lad its just the wheels are slightly turned in the pics i never unlocked the steering when i fitted the wheels haha