Street Zenki S14

[dil]

Well I got this off Danny a few weeks ago after lasting about 4 weeks with a diesel, previously Jimmys 'Magpie 14'. I drove it for about 3 weeks and then parked it to get some bits for it and get it ready for NCT.

Basically just Going to have it as a nice street car, might take it on track once its finished.

Spec as I bought it

s15 ball bearing turbo
front mount intercooler
3" Japspeed exhaust
Bride Brix recliner
Bride low rail
nissan boss
HKS boost gauge
Piaa Racing wheels 18x10j all round
5mm spacers on front
front strut brace
HPi engine dampener
Paddle clutch
kouki rear lights
Vertex front bumper
Vertex Skirts
Uras rear bumper
DMax roof spoiler
HKS 4 branch manifold
Apexi air filter
Samco hoses
Tein coilovers
HKS top mounts
wind deflectors
Not sure what diff but its not a std open diff
silvia mats
Razo pedal covers
Rolled arches and fenders
full respray few months ago

This is how it sits at the moment






Rear wheels are off to clean em up and get some new tyres.
diff is out as I have a 2way sorted to swap in, took the exhaust off too to get at the half shafts more easily.


First thing I did was get a classic Nardi wheel:



The outer tie rod ends were shot so i fitted some new ones.

I also got some internal drive wheels nuts.

Here are some bits I have gathered waiting to put on:

HKS Adj actuator



Downpipe



Walbro fuel pump



GReddy Turbo Timer



Adj Toe Arms



Cusco Adj Camber Arms




Oil temp, Oil Press, Boost and senders




Have a screamer pipe which should come in the post tomorrow.

Have a half cage sorted to pick up in the next few weeks, its a bolt in but I might just weld it in rather than drill through.


Plans for it now are:

- First put an NCT on it!
- Fit all the parts I have.
- Strip the rear seats & sound deadening, paint inside rear either white or pewter grey. Spray the cage some colour and either bolt it in or weld it.
- Decat DONE
- up the boost to 1 bar.
- Sandwich plate and Water temp sensor adapter DONE
- harness for turbo timer DONE
- New coilovers and slam it as the Teins are down to the last already and miles off the ground still!!
- Adj Traction Arms
- Adj Tension Rods
- Fit the 2 way. DONE
- Pressed jap plates
- Water temp gauge DONE
- Rear Strut brace
- Possibly an Alloy Rad, been looking at driftworks supercool rads, anyone running one of these?
- Pistons are seized on my calipers so may go for an r32 rear brake setup. SORTED MY OWN
- SAFC maybe.
- Vented bonnet if one pops up!
- Ganador mirrors

I'l be getting more bits as they pop up for sale so will update when work gets done!


Some inspiration I have!!

[S14a johno]

niccccccccce car buddy
rory on here has s14 as well,
his car come along way, worth a look bud

[alan opel]

looks savage dude !! howd u get on that night in galway?

[Danny O' Sullivan]

cool car dil..if u need any other bits and bobs get onto me...p.s thank fuck u got rid of dat diesel golf

[KerryKid1JZ]

Was wondering where this came out of, seen it around Kilarney a few weeks back has a seriously nice road presence and the Piaa's look sweet under the arches. Well ware

[TwinCamLad]

Shes lookin well man. Hope all goes well for ya

[doug]

a few zenkies popping up lately, always good to see! the wheels look very well under it.