Who to Re-build my sr20ve????

right story goes im looking for someone to rebuild my nissan pulsar vzr N1 engine which wil be stroked out to 2.0.....

I have all the parts needed for the engine to go back together from new oil pump, guides, tensioner chain, seals, acl race bearings custom pistons etc etc....

will need the block bored, honed etc also te crank wil need to checked and reground etc if neccessary....

the head work is all already done...

so basically i need someone to finish out whats left..

but.....

who would ye recommend would be best assemble it...


i know this is a difting site but its an sr after all and a cool sr at that....

Where are ya from?

westmeath\ tipperary

You wont need it bored docco, just honed for new pistons.

Tdp,,,

Quote:

---

Originally Posted by POC

You wont need it bored docco, just honed for new pistons.

---

I presumed ya would need it bored with new pistons no? And the fact it is used block etc...

Quote:

---

Originally Posted by Stonie

Tdp,,,

---

Thay will be doing mapping on it hopefully...

If you want a proper 100% job done on the engine too, bring it to us at TDP and all your machine work and assembly are done in house in a proper environment,, if you can you should,,,

Quote:

---

Originally Posted by Stonie

If you want a proper 100% job done on the engine too, bring it to us at TDP and all your machine work and assembly are done in house in a proper environment,, if you can you should,,,

---

Yea i know robbie is top notch for sr20 motors etc. And prob best to build it but not an option for me at the mintue...

Martin Tracey

Driftma has built a few mighty SR's! Drop him a pm...

Quote:

---

Originally Posted by Backyard performance

Martin Tracey

---

obviously but there not an option at the time being....

Quote:

---

Originally Posted by Famous jh

Driftma has built a few mighty SR's! Drop him a pm...

---

cool i will drop him a pm there now..

also waiting on a couple of quotes....:afro:

Pms replied..........

Looking to get it build in the few weeks...

Bump this up lads....

mike deanes your man i know hes a bit of a trek for you but i would never send my car anywhere else himself and his brother at deaneMsport are fecking magicians

nissan doc...
only joking

TDP if ya can lad...

Quote:

---

Originally Posted by jeff nelson sileighty

mike deanes your man i know hes a bit of a trek for you but i would never send my car anywhere else himself and his brother at deaneMsport are fecking magicians

---

Got a number for him mate... Im in tipp now so not to far for me...

Quote:

---

Originally Posted by bart

nissan doc...
only joking

TDP if ya can lad...

---

Yea i would if i could but Not an option at the minute...im looking for sub 1000 build man.. But if i cant get someone good enough ill send it off to tdp...

Quote:

---

Originally Posted by jeff nelson sileighty

mike deanes your man i know hes a bit of a trek for you but i would never send my car anywhere else himself and his brother at deaneMsport are fecking magicians

---

X2, all work done by the lads is 110%.

Loads of people are turning me down if they never stripped the engine in the first place.. Like WTF.....

pm'd mikes number,

Cool thanks man..

Quote:

---

Originally Posted by docco86

Loads of people are turning me down if they never stripped the engine in the first place.. Like WTF.....

---

thats cos it just such a pain in the hole trying to figure out what the last person is after doing with all the bolts

Well i hav a complete bottom end here of a vzr as im gonna just be using the block that needs to be stripped... Al the head work done so not as big of a mess...

Quote:

---

Originally Posted by docco86

Well i hav a complete bottom end here of a vzr as im gonna just be using the block that needs to be stripped... Al the head work done so not as big of a mess...

---

thats not too bad, but i did one before that i was given a block a head and about 4 boxes of bolts that were all mixed up together now that was fun haha

yea i would imagine so....

but still not that much hassle if ur familiar with sr20s...

Quote:

---

Originally Posted by Moose

pm'd mikes number,

---

never got it man...:huh:

Quote:

---

Originally Posted by docco86

never got it man...:huh:

---

i pm'd it to you there aswell anyway

Cool good man i was into hin this morning..