Good to know :)
What an engine!
Printable View
Good to know :)
What an engine!
unreal lad...
fair play to you..
alot of hard work went into this and its finally payed off...
well done
Cheers lads:)
Christ on a honda 50 thats serious power from an SR !!! congrats :cool:
Why didn't you get Steve Saddler to map it......... Tought you would have after all the hyping up you did about him on here....!
well mapping and engine done, time to get on with the rest!!!
Next ont he list was the suspension and steering! After the event in Portugal where i crashed quite hard there was alot damage done to the steering and suspension.
Bent tein rod end,
Bent tein rod,
broken stock lower arm,
bent steering rack!
Apexperformance have done a fine job and supplied new suspension, so here are the pics of it all!
bent rod end
http://i55.photobucket.com/albums/g1...0sxy/038-5.jpg
bend steering rod
http://i55.photobucket.com/albums/g1...0sxy/037-6.jpg
Apex inverted coilovers
http://i55.photobucket.com/albums/g1...0sxy/009-7.jpg
Full Apex alignment arm set(minus lower arms, stock arms FTW!!)
http://i55.photobucket.com/albums/g1...sxy/010-10.jpg
Some brand new tien rods chopped in half
http://i55.photobucket.com/albums/g1...0sxy/039-2.jpg
http://i55.photobucket.com/albums/g1...0sxy/040-4.jpg
made longer
http://i55.photobucket.com/albums/g1...0sxy/041-2.jpg
http://i55.photobucket.com/albums/g1...0sxy/042-2.jpg
http://i55.photobucket.com/albums/g1...0sxy/043-2.jpg
Chopped the new tension rods a bit
http://i55.photobucket.com/albums/g1...0sxy/011-6.jpg
Fresh strengthened and lower modded arms
http://i55.photobucket.com/albums/g1...0sxy/013-6.jpg
http://i55.photobucket.com/albums/g1...0sxy/016-7.jpg
http://i55.photobucket.com/albums/g1...0sxy/021-8.jpg
http://i55.photobucket.com/albums/g1...0sxy/023-7.jpg
http://i55.photobucket.com/albums/g1...0sxy/024-3.jpg
http://i55.photobucket.com/albums/g1...0sxy/025-4.jpg
I could run more lock if i really wanted to, as the rack sltill has 5-6mm travel befro it bottoms out and its miles from going over centre! But that would be stupid! I think i have enough!
Back end all done
http://i55.photobucket.com/albums/g1...0sxy/044-1.jpg
http://i55.photobucket.com/albums/g1...0sxy/046-2.jpg
GTR back end
http://i55.photobucket.com/albums/g1...0sxy/045-4.jpg
http://i55.photobucket.com/albums/g1...0sxy/047-2.jpg
More sneeks
http://i55.photobucket.com/albums/g1...0sxy/058-2.jpg
http://i55.photobucket.com/albums/g1...200sxy/060.jpg
http://i55.photobucket.com/albums/g1...0sxy/055-3.jpg
http://i55.photobucket.com/albums/g1...0sxy/064-1.jpg
Steve has supported me for the last two years, and i have no doubt in his mapping skills atall!! I sold a few plates to Greg and we done a few deals, got chatting etc, also Greg helped me spec the cams to the engine and has a very good understanding of setting it all up mechanicly, i.e dialing in the cams with a DTI.Quote:
Originally Posted by Robbie Daly Ps13
getting better and better lad..
i like the wishbones....:D:D:D
plates look the job
wow :eek: .........
thats what the girls say when they see mine ........ :eek:Quote:
Originally Posted by git
seriously, coming along nicely .