Stone Broke Motorsport 180sx

Quote:

---

Originally Posted by slithertooth

looking well lad from the progress i seen you'll easy see track time soon ,fair play to ye taking it on and not loosing interest ,i seen what ye started with:eek: and getting it to drive again deserves a back slap

---

i couldnt of done it without your engine, and some other bits lol:D

Cheers man, i hope 2 hav her out on track very soon:cool:

nice build lad. look forward too seein it finished!

savage build a lot of work gone into it looking forward too the end result:cool:

Doing very well:):):):):)

Update time :D

Fitted the 300zx rear hubs and breaks onto the car, i need to extend the copper brake lines 2 meet the hoses from the hubs then the brakes will be fully sorted.

http://i368.photobucket.com/albums/o...d/101_3971.jpg
http://i368.photobucket.com/albums/o...d/101_3973.jpg

Also swapped the driftworks spacers for a fuel cell for the back. Goin to look at sinking it into the boot floor or keeping it in the spare wheel in the rear.

Aiming to have the car out on track for the first week in november so any help and advise with the build will be greatly appriceated :)

Car runs and was doing burnouts outside my gaf today :D

I need to weld up the diff tho to get her spinnin the wheels proper tho

Hopin to have her out in portlaoise soon enough:cool:

It has been a while since there has been an update but iv been doing a few small bits to the car.

Ill have the car in a garage over the weekend and ill be sorting as much of the can as i can. Im hoping that the car's gonna be fully sorted mechanically this weekend.

I did pick up a free Uras rear bumper over the weekend. The bumper needs a few small bit of work as theres a few cracks in it........and the fact that the bumper wouldnt fit in the vectra so i cut a part of the bumper so i could close the boot ha ha :D Cheers to alan opel for pickin it up for me, and makin the bumper fit in the boot;)

http://i368.photobucket.com/albums/o...d/101_3981.jpg
http://i368.photobucket.com/albums/o...d/101_3982.jpg
http://i368.photobucket.com/albums/o...d/101_3983.jpg
http://i368.photobucket.com/albums/o...d/101_3984.jpg

Ill fix it with cable ties, the cars prob gonna kiss a wall at some point so i dont need it to be perfect

i picked up a few more bits tonight to fit to the car at the weekend, wanna get as much done as i possibly can.

I got these gauges, not gonna use them all

http://i368.photobucket.com/albums/o...d/101_4009.jpg

I got these alloys for the front of the car as i had the standard rims on the front

http://i368.photobucket.com/albums/o...d/101_4008.jpg

Picked this up, S13 Rear Lower Strut Brace. I have no idea how to fit this!!

http://i368.photobucket.com/albums/o...d/101_4004.jpg

S13 Front Tension Rods

http://i368.photobucket.com/albums/o...d/101_4003.jpg

An oil cooler wich turned out to deffo be for an SR20, all thats missin is the sandwedge plate

http://i368.photobucket.com/albums/o...d/101_4005.jpg
http://i368.photobucket.com/albums/o...d/101_4007.jpg

I also got this half cage for the 180sx, im gonna send this off to my mate and get him to add the front bars to make it a 6 point and to add a few bars to make it stiffer

http://i368.photobucket.com/albums/o...d/101_3997.jpg

Let the madness begin :D

drill holes at the ends of each crack to stop it getting any longer b4 you cable tie it together.

This build has really come on , fair play :D
Look forward to seeing this out in portlaoise someday , will come over for a chat if I remember :o :p
Love what ya did with the bumper to make it fit in "Vicky" haha