My sr rx7 shell

[ken red 180]

as above lads my sr fd3s shell has to go to fund some monies
--------------------------------------------------------------------------------
http://i1120.photobucket.com/albums/l483/keightleyken/hood.jpg

rite the shell comes with everything you need for an SR CONVERSION
yellow stuff pads
drilled and grooved disks + all callipers are reconditioned
braided break lines which cost a fortune
fuel pump + high pressure fuel lines
wielded diff and custom bracket
tein coilovers + ajustable toe arms
custom made intercooler and stainless steel cooler pipes
bran new alloy rad 52mm wide + custom made bracket to hold rad and cooler
twin electric fans
new battery cable and relocated kit + jap battery
mazada boss and sparco deep dish steering wheel 100mm
kill switch + all toggle switches + fuse board
Cusco rear strut brace
custom exhaust
power steering pipes + bottle etc. etc,
light everything working perfect
new fire wall in
custom subframe
very clean shell in general underneath chassis etc,etc, mint

unfortunally i need to shift this to clear up some debts as i was hoping to hold onto it and build it again,, but that day seems to be getting further and further away:(

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9692.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9676.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9678.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9677.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9675.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9672.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9686.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9680.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9670.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9668.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9665.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9666.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9679.jpg

http://i1120.photobucket.com/albums/l483/keightleyken/DSCF9667.jpg

it cost alot of money to fabricate this shell
comes with everything you need for conversion

need engine,box,prop and pedal box to complete

this car is for the person looking for something a little different
handles like a go-kart because of engine position
the SR sits where the rotary sits its that far back

open to genuine offers

[niall s14a]

Have you got a price your thinkin of lad? I'd be interested in this at the right money.

[ken red 180]

i"ll pm ya there ted

[niall s14a]

Pm replied

[skelly]

pm me a price ken

[ken red 180]

bump for something a little different

[ken red 180]

Bump for this

[JohnC]

Was only thinking about something like this the other day!!!

[ken red 180]

its a cool yoke when running,,,, handles like a go-kart over engine mounted where the rotary sits,,,took a lot of work to do but weight distrubition pays off big time,,,,,,
good clean shell over all that has potential,,,
any info needed just shout

[philiphowe]

would you have a clutch master cylinder for an fdlying about?

[ken red 180]

Should have it there somewhere I'll check for ya

[philiphowe]

got one sorted, how much you looking for the alloy radiator?

[ken red 180]

120 lad as i only used it to make a fitting bracket for the car and it cost me 200 of dave in jap performance

[ken red 180]

Rite lads may px this for road bike or motocrosser
Let me know what's out there
Might even consider breaking it although a lot of work went into building it

[ken red 180]

1100euro takes all if anyone interested

[JohnC]

Oh moma!

[ken red 180]

Rite 1000euro takes the lot or I'm going to break it,,,,,, can deliver at the buyers expense,,,,,,,

[niall s14a]

Rite 1000euro takes the lot or I'm going to break it,,,,,, can deliver at the buyers expense,,,,,,,

Ah lad your makin this very hard to resist, I know once I start though I won't know where to stop with it...

[ken red 180]

There all the same Ted as there all money pits in the long run

Its something different with endless options
Set yourself a budget and make it work,,,, 10k ha.ha,ha.

[niall s14a]

What's the story with it ecu wise? Is there much wiring to do after the engine goes in?

[ken red 180]

I have my loom there for it that I had made up however I did cut a plug off it to help out a mate but I could wire it back on
No ECU with the car depending on what sr you throw in you use our own,,,,,,
You basically need ECU running gear pedal box and a prop then happy motoring anything

[ken red 180]

Bump on this have my eye on a bike that I want
Somebody grab a bargain while its there
1000euro takes the lot

[ken red 180]

Rite lads I want this gone to new home before I break the shell down and sell the coilover's disks calipers various bits and pieces,,,,,comes with everything listed and cost me a fortune to be fabricated and to kit it out,,,if someone wants a shell in great condition to finish and have something different well then this is for you otherwise it get's broke and scrapped its a bargain at 1k

1000 euro takes it

[Kruizer]

What condition are the coilovers in fella ?

[jap scrap]

pm me price on front calipers if you decide to break it

[ken red 180]

I'm going to hold off for a week on this to see if it goes then I'll break it
@kruizer coilover's are dirty looking but in PWO tein type HA
@ japscrap if its breaks I'll mail ya with price

[Kruizer]

Cool keep me in mind for them please :)

[SIMO]

Want this sooo bad have ideas buzzin around my head thinkin about it, was in the pub earlier talkin about it!!! Guna see what cash i can pull together to get this!!!

[jap scrap]

I'm going to hold off for a week on this to see if it goes then I'll break it
@kruizer coilover's are dirty looking but in PWO tein type HA
@ japscrap if its breaks I'll mail ya with price

Cheers man send me a pm when you get a chance


Want this sooo bad have ideas buzzin around my head thinkin about it, was in the pub earlier talkin about it!!! Guna see what cash i can pull together to get this!!!

Do buy it i will make it cheaper on you and i will take the calipers

[ken red 180]

Want this sooo bad have ideas buzzin around my head thinkin about it, was in the pub earlier talkin about it!!! Guna see what cash i can pull together to get this!!!

Well simo its cheap as chips at 1k with everything threw in,,,but I won't take a cent less as its worth More than that to break it
Sure put up a few quid and give me a shout,,,

I bought light covers and stuff off you for this I think,,,,,your out the back of nenagh,, yeah

[SIMO]

Yeah man u got the carbon fiber bonnet and the vented light cover off me!!! Just looking into doin a bit of debt collection at the moe see what i can pull together, just a few questions for ya.

Had you to get a custom prop made for the sr to fit the rx7 or is the engine situated that u can use a standard prop for it??

Have u still got the pedel box or you holding onto that?

Did you do anything to the lock on the front cuz they do have a shit lock if i remember my one correct it wasnt great.

[ken red 180]

I was using an rb25 box in nine so I had to get the prop made,,,,
You will have to do the same
I've never tried a standard one for size,,,,,,


The pedal box is gone into a rally car,,,,,the existing pedals are still there you could try to fit them back in or just pick up pedal box is prob much handy in my opinion

In relation to the steering lock I just put a euro coin in both sides and it gave me that little bit exextra,,,,and it helped as I had 18x 10's on it,,,,,the lock in general wasn't too bad but you could always add another euro or two to get ya out

[ken red 180]

Putting this up one last time as I had someone for it but it turned out they could not find the funds
1000euro takes the lot including a bran new rad custom made intercooler kill switches toggle switches race battery relocation kit rx boss with sparco deep fish wheel coilover's drilled and grooved disks yellow stuff pads coilover's custom made subframe braided break lines all round high pressure fuel lines custom exhaust lots and lots of extras the works
New fire wall in
1000euro takes it away or its being broke but honestly I'd rather see someone get use for it as it cost me roughly 3500e to get it to what it is at the min,,,,,

1000euro
May PX try me

[ken red 180]

Lock this one away
I put this up on donedeal this morning and sold it straight away for more than my asking price,,,,,
Ha,ha,ha, this doesn't happen often,,,,
SOLD SOLD SOLD SOLD SOLD SOLD