PDA

View Full Version : Removing Double Sided Tape from Body Work


cork kouki
22-03-11, 23:25
As above, whats the best way to take doble sided tape off bodywork.
Dont wanna have to repaint the boot door after like.
Cheers
Chuck_g
22-03-11, 23:26
Peal off the other stuff, as much as you can...then use Tar and Glue remover, serious tack :)
Diesel-Dick
22-03-11, 23:26
heat gun and peel it off slowly ;)
Stevo
22-03-11, 23:27
Hammer and chisel ;)
gem-s13
22-03-11, 23:30
Hammer and chisel ;)

rough man 9inch angle grinder with a wire brush!! haha

if you no any pannel beaters man one of them may have a toffe wheel, they will no what it is!! small rubber wheel that goes in a drill its made of some fancy shit that doesnt harm the paint but eats the tape!! great fucking yoke!!
cork kouki
22-03-11, 23:33
Peal off the other stuff, as much as you can...then use Tar and Glue remover, serious tack :)

Tar and glue remover why didnt i think of that?:o
Iv that autoglym tar remover here, would that do the trick or what would be better:)


heat gun and peel it off slowly ;)
Ya will give it a go with the heat gun first to get as much as i can of it off


Hammer and chisel ;)
last resort:p lol
git
22-03-11, 23:33
rough man 9inch angle grinder with a wire brush!! haha

if you no any pannel beaters man one of them may have a toffe wheel, they will no what it is!! small rubber wheel that goes in a drill its made of some fancy shit that doesnt harm the paint but eats the tape!! great fucking yoke!!

sounds like its sometn a magician has :D
nikkisixx69
22-03-11, 23:34
Hammer and chisel ;)


rough man 9inch angle grinder with a wire brush!! haha

fucking LOL!!!:D
cork kouki
22-03-11, 23:36
rough man 9inch angle grinder with a wire brush!! haha

if you no any pannel beaters man one of them may have a toffe wheel, they will no what it is!! small rubber wheel that goes in a drill its made of some fancy shit that doesnt harm the paint but eats the tape!! great fucking yoke!!

Ya there was a lad sayin something to me about a wheel kinda jobbie that goes on a drill allright, was just see'in if there was some way i could do it myself first

Iv the name of it now anyway:)
m-sykes
22-03-11, 23:47
i used vinegar to take of the sticky shit from window tint, try that....did a serious job on tint
pinny
22-03-11, 23:57
panel wipe is the job
hunty_sideways
23-03-11, 00:20
Avery glue remover otherwise heat gun and roll it back till ya get it all of ;)
lukeworx
09-04-11, 16:04
heat gun then small drop of petrol of a clean soft cloth
you'll never know it was there
shines14
09-04-11, 16:14
holts tar remover, serious stuff
tamtaf
21-05-11, 22:18
Toffee wheel is the only answer for removing tape left from mouldings and the sticky pads that hold numberplates on, then use panel wipe for any small bits that may be left on the bodywork. Make sure and keep moving the toffee wheel or YOU WILL burn the paint.
20vees
22-05-11, 23:43
heat gun then small drop of petrol of a clean soft cloth
you'll never know it was there

lets hope he gets it the right way around or the whole thing goes up in flames ha ha ha
cork kouki
23-05-11, 00:15
lets hope he gets it the right way around or the whole thing goes up in flames ha ha ha

Ha ha nope it all came off a treat ;)
m3con
11-06-11, 22:16
aye panel wipe good job for that
k1984w
13-08-11, 12:42
Ye that the best way the rubber wheel on the drill and doesn't damage the paint
Magic21
18-08-11, 21:42
Petrol works a treat for getting sticky residue off.
bandit
19-08-11, 09:12
as said rubber wheel on a drill and it will come off no bother

like this one here
http://solutions.3m.com/wps/portal/3M/en_US/Manufacturing/Industry/Product-Catalog/Online-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQGLE0_nid=L03BT0580SgsS QSFJR0R56glNZ5R4RTPNBbl